Differences

This shows you the differences between two versions of the page.

--- project:networkinglab:alteon-ad3 [2017/03/26 01:09] – created ruza
+++ project:networkinglab:alteon-ad3 [2017/03/26 20:39] (current) – [Factory reset] ruza
@@ Line 5: / Line 5: @@
 ==== Manual ====
 {{ :project:networkinglab:alteon-ad3-ad4-180e-212779-a.pdf |}}
+==== Factory reset ====
+  - connect via serial cable (9600 8N1 NOR)
+  - do cold boot using power switch on the back of the box
+  - during first messages scrolling on the terminal press <Esc>. Default password is "admin".
+  <code>
+  Boot version 10.0.30.7
+  Press <esc> for maintenance kernel
+  Booting maintenance kernel...
+  Enter administrator password:
+  Maintenance Kernel Version 8.0.30 Time:  4:37:08 Sun Mar 26, 2017
+  ------------------------------------------------------------
+  [Main Menu]
+        diag    - Diagnostics
+        boot    - Boot menu
+        cfg     - Configuration Menu
+        debug   - Debugging Menu
+  >> Main# boot
+  ------------------------------------------------------------
+  [Boot Options Menu]
+        reset   - Reset switch
+        image   - Select software image to use on reset
+        conf    - Select config block to use on next boot
+  >> Boot Options# conf
+  Currently set to use active config block on next boot.
+  Specify new block to use ["active"/"backup"/"factory"]:  factory
+  Next boot will use factory default config block instead of active.
+  >> Boot Options# reset
+  Resetting switch ...
+  Boot version 10.0.30.7
+  Press <esc> for maintenance kernel....
+  Alteon AD3
+  Rebooted because of power cycle.
+  Booting complete  4:51:55 Sun Mar 26, 2017:
+    Version 10.0.30.7 from FLASH image1, factory default config block.
+  Enter password:
+  System Information at  4:52:16 Sun Mar 26, 2017
+  Alteon AD3
+  sysName:
+  sysLocation:
+  Switch is up 0 days, 0 hours, 0 minutes and 21 seconds.
+  Last boot:  4:51:55 Sun Mar 26, 2017 (power cycle)
+  MAC address: 00:60:cf:46:a1:e0    IP (If 1) address: 0.0.0.0
+  Hardware Revision: B
+  Hardware Part No: B04_5A-D_7B-A
+  Software Version 10.0.30.7-SSH (FLASH image1), factory default configuration.
+  The switch is booted with factory default configuration.
+    To ease the configuration of the switch, a "Set Up" facility which
+    will prompt you with those configuration items that are essential
+    to the operation of the switch is provided.
+  Would you like to run "Set Up" to configure the switch? [y/n]
+  ------------------------------------------------------------
+  [Main Menu]
+        info    - Information Menu
+        stats   - Statistics Menu
+        cfg     - Configuration Menu
+        oper    - Operations Command Menu
+        boot    - Boot Options Menu
+        maint   - Maintenance Menu
+        diff    - Show pending config changes  [global command]
+        apply   - Apply pending config changes [global command]
+        save    - Save updated config to FLASH [global command]
+        revert  - Revert pending or applied changes [global command]
+        exit    - Exit  [global command, always available]
+  >> Main# save
+  No changes need saving, but since the last boot used the
+   factory default configuration, this save will write that
+   configuration out to FLASH as the "active" config block.
+  Request will first copy the FLASH "active" config to "backup",
+   then overlay FLASH "active" with new config.
+  Confirm saving to FLASH [y/n]: y
+  New config successfully saved to FLASH.
+  Switch is currently set to use factory default config block on next boot.
+  Do you want to change that to the active config block? [y/n] y
+  Next boot will use active config block.
+  >> Main# maint
+  ------------------------------------------------------------
+  [Maintenance Menu]
+        sys     - System Maintenance Menu
+        fdb     - Forwarding Database Manipulation Menu
+        debug   - Debugging Menu
+        arp     - ARP Cache Manipulation Menu
+        route   - IP Route Manipulation Menu
+        uudmp   - Uuencode FLASH dump
+        ptdmp   - tftp put FLASH dump to tftp server
+        cldmp   - Clear FLASH dump
+        panic   - Dump state information to FLASH and reboot
+        tsdmp   - Tech support dump
+  >> Maintenance# panic
+  Confirm dump and reboot [y/n]: y
+  Starting system dump...done.
+  Rebooting at  4:55:40 Sun Mar 26, 2017...
+  </code>
+==== Internals ====
+[[https://goo.gl/photos/6mbnfbr3zLt5dA9N6|fotky]]